IT専門者になりたいの夢

http://www.pass4test.jp

RedHatのRH302認定試験の問題集

Pass4Testの商品は100%の合格率を保証いたします。Pass4TestはITに対応性研究続けて、高品質で低価格な問題集が開発いたしました。Pass4Testの商品の最大の特徴は20時間だけ育成課程を通して楽々に合格できます。

Pass4Testは客様の要求を満たせていい評判をうけいたします。たくさんのひとは弊社の商品を使って、試験に順調に合格しました。そして、かれたちがリピーターになりました。Pass4Testが提供したRedHatRH302試験問題と解答が真実の試験の練習問題と解答は最高の相似性があり、一年の無料オンラインの更新のサービスがあり、100%のパス率を保証して、もし試験に合格しないと、弊社は全額で返金いたします。

RedHatRH302の認定試験に合格すれば、就職機会が多くなります。Pass4TestはRedHatRH302の認定試験の受験生にとっても適合するサイトで、受験生に試験に関する情報を提供するだけでなく、試験の問題と解答をはっきり解説いたします。

試験番号:RH302問題集
試験科目:RedHat 「Red Hat Certified Engineer on Redhat Enterprise Linux 5 (Labs)」

RedHatRH302認定試験は今IT業界の人気試験で多くのIT業界の専門の人士がITの関連の認証試験を取りたいです。RedHatの認証試験の合格書を取ってから更にあなたのIT業界での仕事にとても助けがあると思います。

IT業界の中でたくさんの野心的な専門家がいって、IT業界の中でより一層頂上まで一歩更に近く立ちたくてRedHatRH302試験に参加して認可を得たくて、RedHatRH302試験が難度の高いので合格率も比較的低いです。RedHatRH302試験を申し込むのは賢明な選択で今のは競争の激しいIT業界では、絶えず自分を高めるべきです。しかし多くの選択肢があるので君はきっと悩んでいましょう。

購入前にお試し,私たちの試験の質問と回答のいずれかの無料サンプルをダウンロード:http://pdf.pass4test.jp/RH302.pdf

NO.1 Or

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.2 CORRECT TEXT
One Logical Volume is created named as myvol under vo volume group and is mounted. The Initial Size
of that Logical Volume is 400MB. Make successfully that the size of Logical Volume 200MB without losing
any data. The size of logical volume 200MB to 210MB will be acceptable.
Answer and Explanation:
1. First check the size of Logical Volume: lvdisplay /dev/vo/myvol
2. Make sure that the filesystem is in a consistent state before reducing:
# fsck -f /dev/vo/myvol
3. Now reduce the filesystem by 200MB.
# resize2fs /dev/vo/myvol 200M
4. It is now possible to reduce the logical volume.
#lvreduce /dev/vo/myvol -L 200M
4. Verify the Size of Logical Volume: lvdisplay /dev/vo/myvol
5. Verify that the size comes in online or not: df -h

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.3 Press w to write on partitions table.

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.4 CORRECT TEXT
One Package named zsh is dump on ftp://server1.example.com under /pub/updates directory and your
FTP server is 192.168.0.254. Install the package zsh.
Answer and Explanation:
1. rpm -ivh ftp://server1/example.com/pub/updates/zsh-*
or
1. Login to ftp server : ftp ftp://server1.example.com using anonymous user.
2. Change the directory: cd pub and cd updates
3. Download the package: mget zsh-*
4. Quit from the ftp prompt : bye
5. Install the package
6. rpm -ivh zsh-*
7. Verify either package is installed or not : rpm -q zsh

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.5 CORRECT TEXT
The System you are using is for NFS (Network File Services). Some important data are shared from your
system. Make automatically start the nfs and portmap services at boot time.
Answer and Explanation:
We can control the services for current session and for next boot time also. For current Session,we use
service servicename start or restart or stop or status. For automatically on next reboot time:
1. chkconfig servicename on or off
eg: chkconfig nfs on
chkconfig portmap on
or
ntsysv
Select the nfs and portmap services.
2. Reboot the system and identify whether services are running or not.

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.6 It will ask for the Starting Cylinder: Use the Default by pressing Enter Key.

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.7 vi /etc/fstab

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.8 mkdir /mnt/neo

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.9 CORRECT TEXT
Set the Hostname station?.example.com where ? is your Host IP Address.
Answer and Explanation:
1. hostname station?.example.com ¨¤ This will set the host name only for current session. To set
hostname permanently.
2. vi /etc/sysconfig/network
HOSTNAME=station?.example.com
3. service network restart

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.10 CORRECT TEXT
You are giving RHCT Exam and in your Exam paper there is a question written, make successfully ping to
192.168.0.254.
Answer and Explanation:
In Network problem thinks to check:
1. IP Configuration: use ifconfig command either IP is assigned to interface or not?
2. Default Gateway is set or not?
3. Hostname is set or not?
4. Routing problem is there?
5. Device Driver Module is loaded or not?
6. Device is activated or not?
Check In this way:
1. use ifconfig command and identify which IP is assigned or not.
2. cat /etc/sysconfig/network ¨¤ What, What is written here. Actually here are these parameters
NETWORKING=yes or no
GATEWAY=x.x.x.x
HOSTNAME=?
NISDOMAIN=?
-Correct the file
3. Use vi /etc/sysconfig/network-scirpts/ifcfg-eth0 and check the proper options
DEVICE=eth0
ONBOOT=yes
BOOTPROTO=static
IPADDR=x.x.x.x
NETMAKS=x.x.x.x
GATEWAY=x.x.x.x
4. Use service network restart or start command

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.11 CORRECT TEXT
Your System is configured in 192.168.0.0/24 Network and your nameserver is 192.168.0.254.
Make successfully resolve to server1.example.com.
Answer and Explanation:
Very Easy question, nameserver is specified in question,
1. vi /etc/resolv.conf
nameserver 192.168.0.254
2. host server1.example.com

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.12 Press P to verify the partitions lists and remember the partitions name.

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.13 mke2fs -j /dev/hda? ¨¤ To create ext3 filesystem.

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.14 CORRECT TEXT
There is one partition /dev/hda14 mounted on /data. The owner of /data is root user and root group. And
Permission is full to owner user, read and execute to group member and no permission to others. Now
you should give the full permission to user user1 without changing pervious permission.
Answer and Explanation:
We know that every files/directories are owned by certain user and group. And Permissions are defines to
owner user, owner group and other.
-rwxr-x--- ¨¤Full permission to owner user, read and write to owner group and no permission to
others.
According to question: We should give the full permission to user user1 without changing the previous
permission.
ACL (Access Control List), in ext3 file system we can give permission to certain user and certain group
without changing previous permission. But that partition should mount using acl option.
Follow the stepsvi /etc/fstab
/dev/hda14 /data ext3 defaults,acl 0 1Either Reboot or use: mount -o remount /datasetfacl -m
u:user1:rwx /dataVerify using: getfacl /data

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.15 CORRECT TEXT
There is a server having 172.24.254.254 and 172.25.254.254. Your System lies on 172.24.0.0/16.
Make successfully ping to 172.25.254.254 by Assigning following IP: 172.24.0.x Where x is your station
number.
Answer and Explanation:
1. vi /etc/sysconfig/network-scripts/ifcfg-eth0
DEVICE=eth0
BOOTPROTO=static
ONBOOT=yes
IPADDR=x.x.x.x
NETMASK=x.x.x.x
2. Enter the IP Address as given station number by your examiner: example: 172.24.0.1
3. Enter Subnet Mask
4. Enter Default Gateway and primary name server
5. press on ok
6. ifdown eth0
7. ifup eth0
8. verify using ifconfig
In the lab server is playing the role of router, IP forwarding is enabled. Just set the Correct IP and gateway,
you can ping to 172.25.254.254.

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.16 CORRECT TEXT
Change the root Password to redtophat
Answer and Explanation:Boot the system in Single user modeUse the passwd command

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.17 CORRECT TEXT
Add a new logical partition having size 100MB and create the /data which will be the mount point for the
new partition.
Answer and Explanation:Use fdisk /dev/hda ¨¤ To create new parition.Type n ¨¤ For New
partitionsIt will ask for Logical or Primary Partitions. Press l for logical.It will ask for the Starting Cylinder:
Use the Default by pressing Enter Key.Type the Size: +100M ¨¤ You can Specify either Last cylinder of
Size here.Press P to verify the partitions lists and remember the partitions name.Press w to write on
partitions table.Either Reboot or use partprobe command.Use mkfs -t
ext3 /dev/hda?Ormke2fs -j /dev/hda? ¨¤ To create ext3 filesystem.vi /etc/fstabWrite:/dev/hda? /data
ext3 defaults 0 0Verify by mounting on current Sessions also:mount /dev/hda? /data

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.18 CORRECT TEXT
Successfully resolv to server1.example.com where your DNS server is 172.24.254.254
Answer and Explanation:
1. vi /etc/resolv.conf
nameserver 172.24.254.254
2. host server1.example.com

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.19 Use mkfs -t ext3 /dev/hda? Where ? is your partition number

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.20 mount /dev/hda? /mnt/neo
4 CORRECT TEXT
Your System is going use as a router for 172.24.0.0/16 and 172.25.0.0/16. Enable the IP
Forwarding.
Answer and Explanation:
1. echo "1" >/proc/sys/net/ipv4/ip_forward
2. vi /etc/sysctl.conf
net.ipv4.ip_forward=1
/proc is the virtual filesystem, containing the information about the running kernel. To change the
parameter of running kernel you should modify on /proc. From Next reboot the system, kernel will
take the value from /etc/sysctl.conf.
5.CORRECT TEXT
Some users home directory is shared from your system. Using showmount -e localhost command, the
shared directory is not shown. Make access the shared users home directory.
Answer and Explanation:
1. Verify the File whether Shared or not ? : cat /etc/exports
2. Start the nfs service: service nfs start
3. Start the portmap service: service portmap start
4. Make automatically start the nfs service on next reboot: chkconfig nfs on
5. Make automatically start the portmap service on next reboot: chkconfig portmap on
6. Verify either sharing or not: showmount -e localhost
7. Check that default firewall is running on system ? if running flush the iptables using iptables -F and stop
the iptables service.
6.CORRECT TEXT
neo user tried by:
dd if=/dev/zero of=/home/neo/somefile bs=1024 count=70
files created successfully. Again neo tried to create file having 70K using following command:
dd if=/dev/zero of=/home/neo/somefile bs=1024 count=70
But he is unable to create the file. Make the user can create the file less then 70K.
Answer and Explanation:
Very Tricky question from redhat. Actually question is giving scenario to you to implement quota toneo
user. You should apply the quota to neo user on /home that neo user shouldn't occupied space more than
70K.
1. vi /etc/fstab
LABEL=/home /home ext3 defaults,usrquota 0 0 ¨¤ To enable th
quota on filesystem you should mount
the filesystem with usrquota for user quota and grpquota for group quota.
2. touch /home/aquota.user ¨¤Creating blank quota database file.
3. mount -o remount /home ¨¤ Remounting the /home with updated mount options. ou can verify that
/home is mounted with usrquota options or not using mount command.
4. quotacheck -u /home ¨¤ Initialization the quota on /home
5. edquota -u neo /home ¨¤ Quota Policy editor
See the snapshot
Disk quotas for user neo (uid 500):
Filesystem blocks soft hard inodes soft hard
/dev/mapper/vo-myvol 2 30 70 1 0 0
Can you set the hard limit 70 and soft limit as you think like 30.
Verify using the repquota /home command.
7.CORRECT TEXT
One Logical Volume is created named as myvol under vo volume group and is mounted. The Initial Size
of that Logical Volume is 124MB. Make successfully that the size of Logical Volume 245MB without losing
any data. The size of logical volume 240MB to 255MB will be acceptable.
Answer and Explanation:
1. First check the size of Logical Volume: lvdisplay /dev/vo/myvol
2. Increase the Size of Logical Volume: lvextend -L+121M /dev/vo/myvol
3. Make Available the size on online: resize2fs /dev/vo/myvol
4. Verify the Size of Logical Volume: lvdisplay /dev/vo/myvol
5. Verify that the size comes in online or not: df -h
We can extend the size of logical Volume using the lvextend command. As well as to decrease the
size of Logical Volume, use the lvresize command. In LVM v2 we can extend the size of Logical
Volume without unmount as well as we can bring the actual size of Logical Volume on online using
ext2online command.
8.CORRECT TEXT
Quota is implemented on /data but not working properly. Find out the
Problem and implement the quota to user1 to have a soft limit 60 inodes
(files) and hard limit of 70 inodes (files).
Answer and Explanation:
Quotas are used to limit a user's or a group of users' ability to consume disk space. This prevents a small
group of users from monopolizing disk capacity and potentially interfering with other users or the entire
system. Disk quotas are commonly used by ISPs, by Web hosting companies, on FTP sites, and on
corporate file servers to ensure continued availability of their systems.
Without quotas, one or more users can upload files on an FTP server to the point of filling a filesystem.
Once the affected partition is full, other users are effectively denied upload access to the disk. This is also
a reason to mount different filesystem directories on different partitions. For example, if you only had
partitions for your root (/) directory and swap space, someone uploading to your computer could fill up all
of the space in your root directory (/). Without at least a little free space in the root directory (/), your
system could become unstable or even crash.
You have two ways to set quotas for users. You can limit users by inodes or by kilobyte-sized disk blocks.
Every Linux file requires an inode. Therefore, you can limit users by the number of files or by absolute
space. You can set up different quotas for different filesystems. For example, you can set different quotas
for users on the /home and /tmp directories if they are mounted on their own partitions.
Limits on disk blocks restrict the amount of disk space available to a user on your system. Older versions
of Red Hat Linux included LinuxConf, which included a graphical tool to configure quotas.
As of this writing, Red Hat no longer has a graphical quota configuration tool. Today, you can configure
quotas on RHEL only through the command line interface.
1. vi /etc/fstab
/dev/hda11 /data ext3 defaults,usrquota 1 2
2. Either Reboot the System or remount the partition.
Mount -o remount /dev/hda11 /data
3. touch /data/aquota.user
4. quotacheck -ufm /data
5. quotaon -u /data
6. edquota -u user1 /data
and Specified the Soft limit and hard limit on opened file.
To verify either quota is working or not:
Soft limit specify the limit to generate warnings to users and hard limit can't cross by the user. Use the
quota command or repquota command to monitor the quota information.
9.CORRECT TEXT
One Logical Volume named lv1 is created under vg0. The Initial Size of that Logical Volume is 100MB.
Now you required the size 500MB. Make successfully the size of that Logical Volume 500M without losing
any data. As well as size should be increased online.
Answer and Explanation:
The LVM system organizes hard disks into Logical Volume (LV) groups. Essentially, physical hard disk
partitions (or possibly RAID arrays) are set up in a bunch of equal-sized chunks known as Physical
Extents (PE). As there are several other concepts associated with the LVM system, let's start with some
basic definitions:
* Physical Volume (PV) is the standard partition that you add to the LVM mix. Normally, a physical volume
is a standard primary or logical partition. It can also be a RAID array.
* Physical Extent (PE) is a chunk of disk space. Every PV is divided into a number of equal sized
PEs. Every PE in a LV group is the same size. Different LV groups can have different sized PEs.
* Logical Extent (LE) is also a chunk of disk space. Every LE is mapped to a specific PE.
* Logical Volume (LV) is composed of a group of LEs. You can mount a filesystem such as /home
and /var on an LV.
* Volume Group (VG) is composed of a group of LVs. It is the organizational group for LVM. Most
of the commands that you'll use apply to a specific VG.
1. Verify the size of Logical Volume: lvdisplay /dev/vg0/lv1
2. Verify the Size on mounted directory: df -h or df -h mounted directory name
3. Use : lvextend -L+400M /dev/vg0/lv1
4. resize2fs /dev/vg0/lv1 ¨¤ to bring extended size online.
5. Again Verify using lvdisplay and df -h command.
10.CORRECT TEXT
Create one partitions having size 100MB and mount it on /data.
Answer and Explanation:
1. Use fdisk /dev/hda ¨¤ To create new partition.
2. Type n ¨¤ For New partitions
3. It will ask for Logical or Primary Partitions. Press l for logical.
4. It will ask for the Starting Cylinder: Use the Default by pressing Enter Key.
5. Type the Size: +100M ¨¤ You can Specify either Last cylinder of Size here.
6. Press P to verify the partitions lists and remember the partitions name.
7. Press w to write on partitions table.
8. Either Reboot or use partprobe command.
9. Use mkfs -t ext3 /dev/hda?
Or
mke2fs -j /dev/hda? ¨¤ To create ext3 filesystem
10. vi /etc/fstab
Write:
/dev/hda? /data ext3 defaults 1 2
11. Verify by mounting on current Sessions also:
mount /dev/hda? /data
11 CORRECT TEXT
You are new System Administrator and from now you are going to handle the system and your
main task is Network monitoring, Backup and Restore. But you don't know the root password.
Change the root password to redhat and login in default Runlevel.
Answer and Explanation:
When you Boot the System, it starts on default Runlevel specified in /etc/inittab:
Id:?:initdefault:
When System Successfully boot, it will ask for username and password. But you don't know the
root's password. To change the root password you need to boot the system into single user mode.
You can pass the kernel arguments from the boot loader.
1. Restart the System.
2. You will get the boot loader GRUB screen.
3. Press a and type 1 or s for single mode
ro root=LABEL=/ rhgb queit s
4. System will boot on Single User mode.
5. Use passwd command to change.
6. Press ctrl+d
12 CORRECT TEXT
There are more then 400 Computers in your Office. You are appointed as a System Administrator.
But you don't have Router. So, you are going to use your One Linux Server as a Router. How will you
enable IP packets forward?
Answer and Explanation:
1. /proc is the virtual filesystem, we use /proc to modify the kernel parameters at running time.
# echo "1" >/proc/sys/net/ipv4/ip_forward
2. /etc/sysctl.conf ¨¤ when System Reboot on next time, etc/rc.d/rc.sysinit scripts reads the file
/etc/sysctl.conf. To enable the IP forwarding on next reboot also you need to set the parameter.
net.ipv4.ip_forward=1
Here 0 means disable, 1 means enable.
13.CORRECT TEXT
You Completely Install the Redhat Enterprise Linux 5 on your System. While start the system, it's
giving error to load X window System. How will you fix that problem and make boot successfully
run X Window System.
Answer and Explanation:
Think while Problems occurred on booting System on Runlevel 5 (X Window)./tmp is full ornotQuota is
already reachedVideo card or resolution or monitor is misconfigured.xfs service is running or not.
Do These:
1. df -h /tmp ¨¤ /tmp is full remove the unnecessary filequota username ¨¤ if quota is alread
reached remove unnecessary file from home directory.Boot the System in runlevel 3.¨¤ you can
pass the Kernel Argument from boot loader.Use command: system-config-display ¨¤ It will display a
dialog to configure the monitor, Video card, resolution etc.Set the Default Runlevel 5 in /etc/inittab
id:5:initdefault:
6. Reboot the System you will get the GUI login Screen.
14 CORRECT TEXT
There are two different networks, 192.168.0.0/24 and 192.168.1.0/24. Your System is in
192.168.0.0/24 Network. One RHEL 5 Installed System is going to use as a Router. All required
configuration is already done on Linux Server. Where 192.168.0.254 and 192.168.1.254 IP
Address are assigned on that Server. How will make successfully ping to 192.168.1.0/24
Network's Host?
Answer and Explanation:
1. vi /etc/sysconfig/network
GATEWAY=192.168.0.254
OR
vi /etc/sysconf/network-scripts/ifcfg-eth0
DEVICE=eth0
BOOTPROTO=static
ONBOOT=yes
IPADDR=192.168.0.?
NETMASK=255.255.255.0
GATEWAY=192.168.0.254
2. service network restart
15 CORRECT TEXT
Make a swap partition having 100MB. Make Automatically Usable at System Boot Time.
Answer and Explanation:
1. Use fdisk /dev/hda ¨¤ To create new partition.
2. Type n ¨¤ For New partition
3. It will ask for Logical or Primary Partitions. Press l for logical.
4. It will ask for the Starting Cylinder: Use the Default by pressing Enter Key.
5. Type the Size: +100M ¨¤ You can Specify either Last cylinder of Size here.
6. Press P to verify the partitions lists and remember the partitions name. Default System ID is 83
that means Linux Native.
7. Type t to change the System ID of partition.
8. Type Partition Number
9. Type 82 that means Linux Swap.
10. Press w to write on partitions table.
11. Either Reboot or use partprobe command.
12. mkswap /dev/hda?¨¤ To create Swap File system on partition.
13. swapon /dev/hda?¨¤ To enable the Swap space from partition.
14. free -m ¨¤ Verify Either Swap is enabled or not.
15. vi /etc/fstab
/dev/hda? swap swap defaults 0 0
16. Reboot the System and verify that swap is automatically enabled or not.
16.CORRECT TEXT
You are a System administrator. Using Log files very easy to monitor the system. Now there are 50
servers running as Mail, Web, Proxy, DNS services etc. You want to centralize the logs from allservers
into on LOG Server. How will you configure the LOG Server to accept logs from remote host ?
Answer and Explanation:
By Default system accept the logs only generated from local host. To accept the Log from otherhost
configure:
1. vi /etc/sysconfig/syslog
SYSLOGD_OPTIONS="-m 0 -r"
Where
-m 0 disables 'MARK' messages.
-r enables logging from remote machines
-x disables DNS lookups on messages recieved with -r
2. service syslog restart
17 CORRECT TEXT
You are giving the debug RHCT exam. The examiner told you that the password of root is redhat.
When you tried to login displays the error message and redisplayed the login screen. You
changed the root password, again unable to login as a root. How will you make Successfully Login as a
root.
Answer and Explanation:
When root unable to login into the system think:
1. Is password correct?
2. Is account expired?
3. Is terminal Blocked?
Do these Steps:Boot the System on Single user mode.Change the passwordCheck the account expire
date by using chage -l root command.
If account is expired, set net expire date: chage -E "NEVER" root
1. Check the file /etc/securetty ¨¤ Which file blocked to root login from certain terminal
2. If terminal is deleted or commented write new or uncomment.
3. Reboot the system and login as a root.

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.21 CORRECT TEXT
Create the partition having 100MB size and mount it on /mnt/neo
Answer and Explanation:
1. Use fdisk /dev/hda ¨¤ To create new partition.
2. Type n ¨¤ For New partitions
3. It will ask for Logical or Primary Partitions. Press l for logical.

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.22 CORRECT TEXT
There are two different networks 192.168.0.0/24 and 192.168.1.0/24. Where 192.168.0.254 and
192.168.1.254 IP Address are assigned on Server. Verify your network settings by pinging
192.168.1.0/24 Network's Host.
Answer and Explanation:
1. vi /etc/sysconfing/network
NETWORKING=yes
HOSTNAME=station?.example.com
GATEWAY=192.168.0.254
2. service network restart
Or
1. vi /etc/sysconfig/network-scripts/ifcfg-eth0
DEVICE=eth0
ONBOOT=yes
BOOTPROTO=static
IPADDR=X.X.X.X
NETMASK=X.X.X.X
GATEWAY=192.168.0.254
2. ifdown eth0
3. ifup eth0

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.23 CORRECT TEXT
Dig Server1.example.com, Resolve to successfully through DNS Where DNS server is
172.24.254.254
Answer and Explanation:
#vi /etc/resolv.conf
nameserver 172.24.254.254
# dig server1.example.com
#host server1.example.com
DNS is the Domain Name System, which maintains a database that can help your computer
translate domain names such as www.redhat.com to IP addresses such as 216.148.218.197. As
no individual DNS server is large enough to keep a database for the entire Internet, they can refer
requests to other DNS servers.
DNS is based on the named daemon, which is built on the BIND (Berkeley Internet Name Domain)
package developed through the Internet Software Consortium
Users wants to access by name so DNS will interpret the name into ip address. You need to specify the
Address if DNS server in each and every client machine. In Redhat Enterprise Linux, you need to specify
the DNS server into /etc/resolv.conf file.
After Specifying the DNS server address, you can verify using host, dig and nslookup commands.

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.24 Write:

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.25 CORRECT TEXT
Make Successfully Resolve to server1.example.com where DNS Server is 192.168.0.254.
Answer and Explanation: 1. vi /etc/resolv.conf
Write : nameserver 192.168.0.254

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.26 CORRECT TEXT
Your system is giving error while booting on Runlevel 5 . Make successfully boot your system in
runlevel 5.
Answer and Explanation:
While you load the X Window System, you will get the problem. To troubleshoot follow the
following steps:
1. Check the /tmp is full ?
2. Check your quota, hard limit is already crossed ?
3. Check xfs service is running ?
4. Boot the system on runlevel 3 and execute the system-config-display command
5. Edit the /etc/inittab to set default runlevel 5.
id:5:initdefault:

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.27 Type the Size: +100M ¨¤ You can Specify either Last cylinder of Size here.

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.28 Either Reboot or use partprobe command.

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.29 Verify by mounting on current Sessions also:

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

NO.30 /dev/hda? /mnt/neo ext3 defaults 1 2

RedHat   RH302   RH302練習問題   RH302認証試験   RH302

投稿日: 2013/4/4 3:07:20  |  カテゴリー: RedHat  |  タグ: RedHatRH302